Tag Archives: mold making

Hanging Wall Tiles

IMG_5962

 

Wall hanging tiles are a new part of the Magic Box project that we have been working on.  Like the house, the mold was made for this in July.  This mold was designed by Gabe and is intended to mimic gallery wrapped canvas.  The piece is large (16″x15″x2″) and was constructed initially from wood wrapped in a heavy burlap.  The top pic shows Gabe taking the mold apart after the plaster was poured.  The piece by piece construction allowed the box to be removed cleanly without damaging the plaster.  The second shows the finished piece.IMG_6001 IMG_6177 IMG_6178Once the mold was dry, we were ready to press.  The first slabs for this were 3/8″ and weighed about 15 lbs.  This weight was usually enough to build the supports from as well, provided the slab was well-shaped before pressing.  The photo of the finished tile really shows off the texture.  The initial rules of the press have changed quite a bit as we have made several.  The piece is very large for slab work and has major problems with cracking.  We have adjusted the support structure, slab depth, dry times, clay bodies and added a waster slab.  In spite of all these adjustments, cracking is still a major problem for these pieces.

In addition to the technical exploration I have tried several finishing methods for the surfaces, depending on the image and the condition of the tile.  The first series depicts images taken from The Magic Box film,  These images originated as screen shots and then were translated into paintings or transfers through various methods.

IMG_6659 IMG_6740 IMG_6614 IMG_6741These four pictures show the screen shot after photo manipulation and then the finished image on tile.  These were rendered in oxide and glaze.  This was difficult to control saturation and color gradient and was not attempted again.

IMG_6759 IMG_6751 IMG_6748The other major technique used in the first series was a more graphic approach that relied on decals and glaze effects.  I really love these, in part because they work with the cracking a bit better than the heavily image dependent tiles.  This graphic approach also relies less on images from the film.  Only the house image here is taken directly from the film.  The other two tiles are more descriptive of the development of the characters depicted.

painting tiles1 painting tiles 2 Painting tiles 3IMG_7387The second series saw further development of both the technical clay and surfacing techniques.  The tile above was too badly cracked to glaze fire and so was epoxides and paint finished.  The process of painting ceramic always starts with spray paint for us, the first image shows the tile masked off and the second, the protected drawing after the mask was removed.  The last two are the paint in process.

IMG_7389 IMG_7391The last two tiles combine the techniques used in the first series but rather than oxides, I used commercial underglazes for building the image.  These have a painterly quality that I am interested in, but might benefit from more color.  The series is ongoing, and will likely continue to evolve.

Making Molds for the Empty Room

IMG_6200

Making molds for the house that will be used in our upcoming film, The Empty Room, has been the major focus of the last few weeks.  Using the preliminary drawings and the scale model discussed in the last post, Gabe focused on drawing the transfers.  These are done on trace paper, using a soft lead and a light table designed and made by Gabe.

IMG_6202

 

Each of the transfer pages is an exact map of the clay tile that will be built.  The light table is necessary so the transfers are not backward when they are placed on to the clay slab.

IMG_6208

The trace paper is laid, graphite down, onto the clay surface and smoothed out.  The paper begins to wrinkle and distort almost immediately so this step must be done quickly and precisely.  Once the sheet has had full contact with the clay and is lightly compressed onto the surface, the paper is removed and the clay is ready to work.

IMG_6210

The first step was to trim the borders of the wall.

IMG_6211IMG_6214

Next, the masonry joints were pushed into the slab along lines indicated by the transfer sheet using a custom rib that Gabe made for the purpose.  These lines needed to be exactly the correct size and completely uniform, no tool we had, was able to give exactly what we were looking for, so making the tool was necessary.

IMG_6217IMG_6218

Once the tile was completed, clay walls were built in preparation for plaster casting.  Shrinkage was a major factor as we need the closest size uniformity possible among the tile molds so each of them was cast no more that 12 to 18 hours after they were made.

molds1

Using the paster formula from ceramicartsdaily.org, the tiles were cast.

molds

We ignored the 1″ border that is conventional in mold making so the tiles could be cut exactly to size, using the mold itself as a guide.  This makes the molds extremely fragile, we are using great care in storage and drying.

IMG_6249

 

Each wall needed its own mold because of the intricacy of the brick detail which is correct for structural brick.   In addition to the brick pattern, the third floor has many architectural details and each of the panels needed a full redesign.  At this point we have 13 molds completed with many internal details to continue to resolve, but it is encouraging to see the project so well on its way.

Doll House

The next major project for Foxy-Wolff is another play set/ film project.  The earliest inspiration for this piece comes from Barbie’s Dream House, but early concept is as far as the influence goes.  This work was conceived of at the same time we dreamed up the LLICPS, but is so much more complex to build and film that it has taken a great deal of time to manifest.  IMG_4103Our first job was to decide on the scale of the piece.  We were wanting a larger piece than our small kiln would allow so modules were the best solution.  Another priority of the piece was a high degree of precision.  Molds then became the best solution for the build.  Several ideas were pursued, but in the end a two-part press mold was decided on, allowing uniformity of each wall with both inside and outside detail.  When making a doll house, better follow the rules of doll houses.  Each wall would then need two parts, a floor, a ceiling, a roof joist, roof tiles, trim work, gables, and a staircase; in total 15 separate molds were made.IMG_4108Originals were the first step, after determining desired finish size and calculating shrinkage, patterns were created from heavy paper.  all the decoration was applied to the patterns, then transfers were made using graphite and tracing paper.IMG_4107After the transfer process and the tiles were cut, the decoration needed to be removed from the original.  A border was then added to the tile to provide a wall for the mold.  Registration marks were also cut to help the molds fit back together after the original was removed. IMG_4116 Walls were then built and secured in preparation for the plaster.IMG_4119 once the first side of the wall was poured, the walls and the border was removed and the interior received its transfer image and was carved and prepared for plaster.  Early on we could see that an escape route for the clay was essential.  the tabs at the top and bottom were added to create voids to allow this.  in the end this was not quite enough and plaster had so be dug from the window voids as well.  Another tricky issue with these was the need for the window openings to line up inside and outside.IMG_4150 The plaster was added again.  For our plaster mixing formula we follow the one provided by ceramic arts daily.

http://ceramicartsdaily.org/ceramic-supplies/ceramic-molds/plaster-mixing-101-how-to-mix-plaster-for-ceramic-molds/

The basic advice here is excellent and the ratio is nearly always perfect.  The small batches seems a bit watery, we typically add a little plaster when mixing small.image-2After a few days of drying, the molds were broken into so that the original could be removed and the mold left to dry.  At least a week, but the longer they dry, the better the molds become.IMG_4174 As mentioned above, they piece required many details.  The mold making phase of the project lasted weeks.IMG_4179The stairs proved a different sort of challenge.  As I said, precision is a high priority for the project, I was unsure of how to get what I wanted with clay and keep it crisp through the build and pour.  This bit was handed off to Gabe and he engineered and built this beauty in a couple of hours.  This mold was not only huge time-saving but its crisp lines really makes the look of the piece.IMG_4180The roof and the ceiling were difficult to design, this is how the module aspect of each floor works, with locking tabs in the floor and roof of each story. Also critical is tying the porch to the stairs so that the characters can move from floor to floor smoothly.IMG_4181Once the molds were built we had to learn how to use them.  The stairs were a particular challenge, keeping that crisp line and filling all of the cracks and gaps took several tries and approaches.IMG_4186As the molds were dried and their techniques for use were understood, we were ready for the build.  More on that soon.

Play Set Action Figures and Making a Two Part Mold

IMG_3530 IMG_3534 IMG_3541

The three small objects above are the first attempt at action figures for the play set.  Obviously based on Fisher Price toys from the seventies, I wanted the objects simple and direct and to work with the mold making technique that I am focusing on this semester.  I began with three small pieces of clay that I allowed to dry to leather hard.  Using sketches, I carved the solid figures so that they would have no undercuts so that they could be easily cast and reproduced.  For the video I am wanting to produce several identical objects that can be broken and replaced through the course of the filming.

When the figures were complete I then made forms for the molds using foam core and duct tape. I made the forms in two pieces because the openings are small and I wanted simple access for notching the bottom piece.  The top of the form was attached with more duct tape after the bottom half of the mold was cast.  Rather than setting the object into clay to cast the first half, I placed the figures directly into the wet plaster after it had a moment to slightly set.  This was a great innovation in several ways, however the figures did slip and move making the molds possibly unusable, especially in the case of the male office worker.

After the molds came out of the forms I separated them using hot water and cleaned them up with a metal loop tool.  While I love the little molds I made, there is no doubt there is much improvement that can be made on them.  I’m looking forward to another try.

IMG_3553IMG_3588IMG_3595